The Tower
Cited by 12 Concordances Compliant with Ordinance 4 Surveyed — partially ISO 8,812 — pending since 11,904

Decimal Flange

MS 0788.82 · Objects and instruments

Decimal Flange is the administrative term for a structural and catalogical feature in which a floor designation terminates in a decimal fraction and is fitted to the stairwell it interrupts. The term is often applied loosely to the floor itself, though the Librarians' standing instruction is that the flange is the fitting, and the floor is what the fitting encloses. Floor 450.5, the most frequently cited example, is classified as a Decimal Flange only in the first sense; in the second sense it is an interstitial space, and the distinction has mattered in at least four recorded disputes.

Construction and registry

A flange is entered in the Register of Outlooks by its decimal remainder rather than by its whole floor, a practice that follows the Schism of the Misplaced Decimal and its ruling that positions recorded to different decimal places are administratively distinct. The remainder governs the flange's classification: the .5 flange is the standard interstitial fitting; the .25 and .75 flanges are quarter-flanges and are narrower; the .1 through .9 flanges are collectively known as the ninth band and are the subject of a long quarrel between the Clerks of the Decimal and the Stairwell Assessors' Office over who may inspect them.

The first flanges are recorded in the Spiral Decimal System recensions of the Regency Era, though the earliest register entry is a marginal note from the winter of 2174 concerning a half-landing on the northwest stair that would not hold its number. The note is signed by the duty clerk, Arveth Sorn, and reads in full: "The landing has been numbered twice. It is willing to be one of the two. Which one is not a matter for me."

Flange tolerance and its breach

Flange tolerance is the permitted deviation between the decimal remainder on the register and the decimal remainder of the floor as installed, expressed in hundredths of a flange-width and sampled by the Assessors on the third Thursday of each quarter. The tolerance is set at 0.03. It was breached in the winter of 2307 on the 814.2 flange, where a repair to the eastern balustrade shifted the stair opening by a little over a quarter-width, and an entire class of records was found to have been catalogued against a floor that no longer existed at its registered position. The matter was not resolved for eleven years; it was disposed of by the Provisional Logging Protocol and the reclassification of the affected holdings under the Doctrine of Whole Integers, which permits a disputed remainder to be resolved by rounding where the rounding is unanimous.

The Dispute of the Fourth Decimal

The reading of flange pressure — the force exerted by a lower floor against an upper one, measured at the fitting — has been the flashpoint of the flange's scholarly history. The practice of disregarding the fourth decimal place in Catalogical Pressure readings was formalized after the Dispute of the Fourth Decimal (2301), whose findings are annex 2 of the Concordance of Structural Readings. The 2301 annex is explicit and is quoted in full in the Assessors' handbook:

"Where a reading is recorded to the fourth decimal, the fourth decimal shall be struck from the record and the reading carried forward at three places. The struck figure may be inspected on request, but shall not be acted upon."

— Concordance of Structural Readings, Annex 2

Three digits were the standard because Decimal Gradation had already fixed the precision of precision itself at three places — the Selvage Decimal System had made three-decimal expression standard in a different context entirely, and its rule appears to have been copied across by a clerk who was working from the wrong shelf. The Assessors have never formally corrected the borrowing; the Clerks of the Decimal hold that the borrowing is not theirs to correct, and the Assessors hold that the figure has held for a century and does not require correction.

There is a competing recension. The Second Concordance of Structural Readings holds that the fourth decimal is not struck but carried, and that the 2301 annex was wrongly transcribed in the seventh printing. The two accounts have never been reconciled; the standard resolution, where the matter arises, is to invoke the Spiral Decimal System and record the reading twice.

Relationship to resonant flanges

Decimal flanges should not be confused with Resonant Flanges, which arise where the Oneiric Hum couples mechanically to the fitting. The distinction is contested in the Oneiric Decimal System, which classifies the hum at sigil 372.441 and records a small number of readings taken on the 450.5 flange itself, at dates the Assessors do not recognise. An apprentice assigned to the decimal flanges in the winter of 2313 was told, on leaving, that he must not carry the flange register above the ground floor. He was not told why. The rule stands and is printed in the register, on the first page, in the same hand as the entry for 2174.

Classification of the .5 floor

Whether a decimal flange is a place or a fitting is not settled and will not be settled by argument of the present kind. The Class Δ notation is used for the .5 floors in the Register of Outlooks, and it is used inconsistently, chiefly by clerks who were working without a full set of the annexes. The Assessors' Manual cautions against citing the .5 flange as precedent for any other position, and the caution is repeated in the manual's marginalia: "The floor is not a number. The flange is a fitting. The stairwell is the fitting. The reader should not proceed further without a numeral."

In the practical sense, the flange is simply what is between them — the half-step up, the landing that does not appear on the north stair plan, and the fitting that makes the number possible. The 4th Sub-Assessors' Office maintains these fittings on a ten-year cycle, and their current schedule lists the 450.5 flange as due for inspection in the spring of 2423, along with a note that the lower half of the balustrade should be re-painted before the Assessor inspects, as it was last painted in the spring of 2413.

See also

Referenced by

Readers also asked

Class Δ (Disputed Decimal): how is it conducted?

Class Δ (Disputed Decimal) is an administrative classification for units of catalogical data whose formal decimal assignment remains contested under two or more valid Concordances. Unlike the more transient designations …

Class Δ (Disputed Decimal)
Selvage Decimal System: how is it conducted?

The System operates on three axiomatic principles, as first formalized in the unpublished appendix to the Third Concordance by M. Selvage:

Selvage Decimal System
Decimal Gradation: how is it conducted?

Decimal Gradation refers to the specialized practice of quantifying and classifying the phenomenological severity or quality of a decimal point's absence, misplacement, or disputed validity within a spiral decimal design…

Decimal Gradation
Clerks of the Decimal: who are they?

The Clerks of the Decimal are the subordinate order charged with the physical custody, transcription, and ceremonial defence of decimal points wherever they appear in Tower records. They are distinct from the Clerks of t…

Clerks of the Decimal

Passages cited from this record

Readers who consulted this also failed to find

Assistance

A Librarian is with you.

MS 9679.39
MS 8532.92
MS 1913.80

The Librarian considers the matter closed.

Typical response time: one Concordance. If your enquiry concerns a holding, consult the finding aid.